Heavy Mobile Equipment Mechanic

Applicants must meet the requirements of the Office of Personnel Management (OPM) Job Qualification System for Trades and Labor Occupations (X-118C). Although a specific length of time and experience is not required for most trade and labor occupations, you must show through experience and training that you possess the quality level of knowledge and skill necessary to perform the duties of the position at the level for which you are applying. Qualification requirements emphasis is on the quality of experience, not necessarily the length of time. Your qualifications will be evaluated on the basis of your level of knowledge, skills, abilities and/or competencies in the job elements and screen out listed below. This job has a screen-out factors which will be used to determine minimum eligibility for this job. Applicants who do not receive a minimum of two points on this screen-out element(s) will be found ineligible. The screen-out element for this position is: Applicants must possess at appointment, and maintain thereafter, a valid U. S. State issued Commercial Driver’s License (CDL- Class A) in order to drive and operate U. S. government owned and leased vehicles and equipment. In addition to the screen-out element you will be evaluated on the following Job Elements through your resume and responses to the on-line assessment questionnaire: Ability To Do The Work Of The Position Without More Than Normal Supervision If your knowledge and ability in the SCREEN OUT factor above is not sufficient, you will receive no further consideration. In preparing your application, describe in detail the experience and training which you have had that specifically prepared you for this job and to perform the duties described for this job. Experience should be clearly described and documented in your resume. The qualifications reviewer will not assume performance of such duties by Job Titles alone. This position has a selective placement factor, failure to meet this requirement(s) will result in an ineligible rating. Must possess a current valid U.S. motor vehicle operator’s license from state of residence and interstate Commercial Driver’s License (CDL), including current DOT medical card with applicable endorsement to meet Federal and State requirements. Ability to perform without more than normal supervision a range of technical corrective and preventive maintenance, including inspecting, diagnosing, repairing, rebuilding, testing, and adjusting on major systems and components of specialized heavy-duty mobile vehicles, and equipment. Experience should include working with heavy construction and earthmoving equipment, aerial man-lifts, hydraulic mobile cranes, and class 8 trucks. Working Conditions A Heavy Mobile Equipment Mechanic works in tiring and uncomfortable positions for long periods of time. The work is physically challenging and requires standing, lying, or sitting. Frequently lifts and carry items, unassisted, weighing up to 75 pounds, often exerts effort in pushing, pulling and position in parts, assemblies, and equipment. Lift and move heavier items with the assistance of other works or with lifting devices such as jacks, hoists, and cranes. Works from ladders or work platforms up to 12 feet (average 2-6 feet). The work is performed both indoors and outdoors. When indoors, the incumbent is frequently exposed to drafts, changing temperatures, and high noise levels, which are difficult to hear and talk above. When outdoors, the incumbent may work in bad weather, mud or snow, and wet or icy areas and conditions. The mechanic is frequently exposed to irritation or discomfort from dust, heat, fumes, and hard damp floors or ground. Typically works on parts systems which are dirty, oily, or greasy. Is frequently exposed to the possibility of receiving cuts, , bruises, electrical shock, sprains, and injury from falls while repairing, positioning, and moving equipment and is often exposed to the possibility of receiving burns and skin irritations from acid, fluids, and lubricants. To reduce the dangers and irritations when performing tasks the mechanic is required to follow prescribed safety practices and use of assigned personal protective equipment such as protective ear devices, eye wear, hard hats, welding hood, hard-toe shoes, respirators, and protective clothing to prevent injury from self or others as well as to protect equipment and work from damage or destruction. Some of these safety items may be uncomfortable to wear or use and may have to be worn or used for long periods. HMEM job(s) may be designated to support multiple facilities throughout BPA’s service territory (organizationally referred to as a mobile mechanic). When assigned, the HMEM may be in a nearly continuous travel status. Physical Requirements Incumbents must be physically and mentally able to efficiently perform the essential duties of the position (such as the ability to work at heights up to 150 feet) with or without reasonable accommodation, without hazard to themselves or others. Essential Functions Corrects deficiencies on all major systems such as engines, power trains, hydraulic suspension, steering and electrical systems, and subsystems on both heavy vehicles and mobile equipment such as bulldozers, road graders, rollers, construction and earth moving equipment; front-end loaders, backhoes, and similar power shovels; mobile cranes; heavy special purpose vehicles such as large transmission line maintenance vehicles, fuel dispensing trucks, and fire trucks; and automobiles and light equipment such as forklifts and snowmobiles. Performs inspections of vehicles and equipment. Utilizes scientific diagnostic equipment to diagnose and correct malfunction of internal and external parts of equipment and vehicles; repairs or replaces power train components, brakes, suspension and steering problems. Utilizes advanced diagnostic techniques and theory to isolate and correct problems in high pressure and extra-high pressure hydraulic systems. Uses technical schematics and drawings as required for trouble-shooting and maintenance of equipment. Uses tools and work equipment such as electric arc and gas welding equipment and mechanical tools. Drives 35% of the time in all weather conditions. “Experience” refers to paid and unpaid experience. Examples of qualifying unpaid experience may include: volunteer work done through National Service programs (such as Peace Corps and AmeriCorps); as well as work for other community-based philanthropic and social organizations. Volunteer work helps build critical competencies, knowledge, and skills; and can provide valuable training and experience that translates directly to paid employment. You will receive credit for all qualifying experience, including volunteer experience. CTAP/ICTAP candidates: To be considered “well qualified” you must meet all of the requirements as described in this section. You must meet ALL qualifications and eligibility requirements by the closing date of this announcement.
The Heavy Mobile Equipment Mechanic (HMEM) performs preventative, predictive and corrective maintenance on BPAs light and heavy mobile equipment fleet.